ASTM E2010窗户组件的正压燃烧试验的标准试验方法


ASTM E2010窗户组件燃烧测试标准

ASTM E2010 Standard Test Method for Positive Pressure Fire Tests of Window Assemblies
ASTM E2010窗户组件的正压燃烧试验的标准试验方法


ASTM E2010标准适用范围

1.1 This test method covers fire-test-response applicable to window assemblies, including glass block and other light transmitting assemblies, for use in walls or partitions to retard the passage of fire (see Appendix X1).

1.2 This fire-test-response test method will determine the ability of window assemblies, including glass block and other light transmitting assemblies, to function as a fire barrier during a standard fire endurance test. Such tests shall not be construed as determining suitability of window assemblies for continued use after fire exposure (see Appendix X1.2).

1.3 This fire-test-response test method is intended to evaluate the ability of window assemblies, including glass block or other light transmitting assemblies, to remain in a wall or partition during a predetermined fire test exposure, which is then followed by the application of a hose stream (see Appendix X1.3).

1.4 The fire exposure is not necessarily representative of all fire conditions, which normally vary with changes in the amount, nature and distribution of fire loading, ventilation, compartment size and configuration, and heat sink characteristics of the compartment. It does, however, provide a relative measure of fire performance of window assemblies under threse specified fire exposure conditions.

1.5 The hose stream test used in this test method is not designed to be representative of an actual hose stream used by a fire department during fire suppression efforts.

1.6 Any variation from the construction or conditions that are tested will possibly change the performance characteristics of the assembly.

1.7 This fire-test-response standard does not provide the following:

1.7.1 The fire endurance of window assemblies in walls or partitions constructed of materials other than those tested.

1.7.2 A temperature measurement on the unexposed surface of the window assembly.

1.7.3 A measurement of smoke or products of combustion that pass through the window assembly.

1.7.4 A measurement of smoke, toxic gases, or other products of combustion generated by the window assembly.

Note 1—The information in 1.7.3 and 1.7.4 may be important in determining the fire hazard or fire risk of window assemblies under actual fire conditions. This information may be determined by other suitable fire test methods. For example, flame spread and smoke development may be determined by Test Method E 84.

1.8 The fire-test-response test method permits through-openings, that are created by cracking, separation, or loss of glazing material, provided they do not exceed specified limits.

1.9 The values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.


我们还提供各种美标防火测试

美国NFPA130测试        
http://www.firete.com/fire_standard/railway/166.html  
ASTM E84表面燃烧性能测试 
http://www.firete.com/standard/usa/759.html  
ASTM E648地板防火性能测试 
http://www.firete.com/standard/usa/296.html  
ASTM E162火焰表面延伸测试 
http://www.firete.com/standard/usa/297.html  
ASTM E662烟密度测试    
http://www.firete.com/standard/usa/1331.html  
BSS7239毒性测试        
http://www.firete.com/standard/usa/293.html


南京睿督公司免费咨询电话:025-8658 3475  400-603-6575
网址:www.fire-test.com
邮箱:[email protected]

 
南京睿督科技有限公司 版权所有 DIN5510 DIN5510-2
地址:中国江苏省南京市江东中路118号德盈大厦16F  电话:(+86) 025-8658 3475
传真:(+86) 025-8658 3457    邮箱:[email protected] 苏ICP备12030029号-3 苏公网安备 32010502010104号
南京睿督科技有限公司是一家专业从事DIN5510等各种不同国家标准机车材料阻燃及烟雾毒性的测试、咨询的机构。